Boral Roof Replacement Nationwide

Boral Roof Replacement in Ventura: What to Know First

Boral roof replacement in Ventura is what we do when a Boral tile or Boral steel roof has reached the end of its serviceable life and patching no longer makes financial sense. As an independent Boral service provider, we typically complete a full Boral tear-off and replacement in 5 to 9 working days depending on roof size, decking condition, and whether we’re matching existing Boral tile profile or switching to a new Boral line. Most Ventura homeowners pay between $18,000 and $42,000 for a complete Boral roof replacement on a 1,800 to 2,600 square foot home, and we give you that written number before the first tile comes off the truck.

Call (559) 249-4917

This page is for Ventura homeowners who already have Boral on their roof and want straight answers about replacement: what fails, what it costs, how long it takes, and whether the warranty still means anything. If you’d rather talk it through, call (559) 249-4917.

How Boral Products Fail – and How We Fix Them

• Boral concrete tile surface spalling near the eaves. We see this constantly on older Boral Villa and Boral Capistrano installations within eight blocks of the Ventura coastline. Salt air works its way into the tile’s surface pores, and after 20-plus years of wet-dry cycles, the face begins to flake off in thin layers. The tile loses its protective fire skin and starts absorbing water, which adds weight and accelerates freeze-thaw cracking on cold winter mornings. The fix is a full replacement of the affected slopes, not a patch, because spalling tiles are compromised across the entire exposure zone.
• Boral steel roof coating delamination on the western exposure. Boral steel panels with older Kynar 500 finishes hold up well inland, but homes in Ventura’s hills above Foothill Road with direct afternoon sun exposure get UV breakdown that flat-roof inspections miss. The coating dulls, then begins lifting at the panel laps. Once moisture gets between the coating and the galvalume substrate, you get rust trails running down the panel faces. We replace these with new Boral steel panels and proper underlayment rather than re-coating, because re-coating over compromised galvalume rarely lasts more than a few years.
• Broken Boral concrete tiles from foot traffic on shallow-pitch sections. Boral tiles are rated for specific minimum slopes, and when we see cracks centered on the center of tiles on low-pitch sections, it’s almost always from someone walking the roof without a proper distribution mat. The tiles crack along the crown, then water finds the underlayment. On replacement, we install the correct Boral profile for the slope and walk with roof jacks and mats, never bare boots on the tile surface.
• Underlayment failure under Boral tile that looks “fine from the street.” The tile itself can last 50 years or more, but the underlayment beneath it often fails at 20 to 25 years, especially in Ventura homes built in the 1980s and 1990s with older asphalt-saturated felt. Water stains on ceilings or soffits without any visible broken tile usually mean the underlayment is gone and the tiles are just shedding water into the deck. A full Boral replacement here includes stripping to the deck, replacing damaged sheathing, and installing a modern synthetic underlayment before the new tile goes down.
• Boral accessory piece mismatch after prior repairs. We’ve walked onto Ventura roofs where a previous repair used a generic field tile instead of the correct Boral hip or ridge cap, leaving gaps where wind-driven rain gets in. Boral profiles have specific accessory geometries, and the wrong cap piece leaves open joints. On replacement, we order the matching Boral accessories and verify the profile code against the existing field tile before install.

Our Boral Roof Replacement Process

1. 1
   Site walk and measurement. We inspect the existing Boral roof, identify the exact profile and color, check decking condition from the attic where accessible, and note any slope-specific challenges or vent flashing problems.
2. 2
   Written scope and price. Before any work starts, you get a written line-item price covering tear-off, disposal, decking replacement allowance, underlayment, Boral tiles and accessories, flashing, and cleanup. The number on the page is the number on the invoice.
3. 3
   Material ordering and delivery. We order your Boral product directly and verify profile and color match before the crew arrives. If you’re switching Boral profiles, we’ll show you samples so there’s no color surprise on install day.
4. 4
   Tear-off and deck inspection. We strip the old tile and underlayment, then inspect every sheet of decking. Rotted or delaminated sheathing gets replaced at the per-sheet price already written in your scope.
5. 5
   Underlayment and tile installation. Synthetic underlayment goes down first, then Boral tiles in the correct exposure for your slope. We install ridge and hip caps with the proper Boral accessories, not aftermarket generics.
6. 6
   Final walk, photos, and written guarantee. We document the finished roof with before-and-after photos, walk the roof with you or send photo proof, and hand you the written 365-Day Done Right Promise. If anything we touched fails within a year, we fix it at no charge.

What Boral Roof Replacement Costs in Ventura

Here’s what we tell Ventura homeowners to expect, based on roof size and Boral product line:

• Boral concrete tile replacement (Capistrano, Villa, or Estate profiles): $18,000 to $38,000 for most Ventura homes. The tile itself runs $9 to $14 per square foot installed, and the tear-off, underlayment, and accessory package adds $5 to $8 per square foot.
• Boral steel replacement: $22,000 to $42,000. Steel panel and trim costs more than concrete tile per square, but the install is faster and the weight load on your framing is lower.
• Roof decking replacement (if needed): $110 to $160 per 4×8 sheet, and older Ventura homes with original plywood often need 10 to 20 sheets replaced once we’re down to the deck.

What moves the price: roof pitch (steep roofs cost more to strip and install), access (homes with tight side yards or overhead wires in the Midtown Ventura corridor add labor time), and whether we’re replacing the entire roof or just the top slopes. Call (559) 249-4917 and we’ll give you a written line-item price for your specific roof.

Why Ventura Homeowners Call Crestview Roofing Co Ventura for Boral Work

We’ve been doing Boral work long enough to know that the tile is only half the system. The underlayment, the flashing, the accessories, and the decking matter just as much to how the roof performs over the next 20 years. Dylan Pace grew up in Los Angeles and trained at Los Angeles Trade-Technical College, where he learned the difference between a roof that looks good on install day and one that still performs a decade later, and he’s carried that standard through every Boral job we’ve done across Ventura County.

We also carry the backup of every major brand. If a Boral tile is discontinued or backordered, we can pivot to GAF, Owens Corning, or CertainTeed with full transparency about what changed and why. Our 365-Day Done Right Promise covers every Boral replacement for a full year in writing. If it’s not in writing, it’s not a promise. And when you call (559) 249-4917, a live person answers.

FAQs

Will replacing my Boral roof void the manufacturer warranty? Boral tile warranties typically cover manufacturing defects in the tile itself, not the roof system, and replacement by an independent contractor does not void that defect coverage as long as the new installation uses proper Boral profiles and accessories. We’re an independent Boral service provider, not the manufacturer, so we can’t speak for every warranty term, but we install to manufacturer specifications.

Can you replace just the broken Boral tiles instead of the whole roof? Sometimes, yes, if the underlayment is still intact and the tile profile is still in production. We’ll do an honest inspection and tell you if a targeted replacement makes sense or if the underlayment failure means a full replacement is the smarter spend. Call (559) 249-4917 and we’ll look at it.

How long does a Boral roof replacement take in Ventura? Most complete Boral tear-offs and replacements take 5 to 9 working days from the first tile off to final cleanup. Weather delays can stretch that, especially during winter rain, but we give you a written timeline before the crew shows up.

What if the final price changes once you’re on the roof? If we find decking damage or structural issues we couldn’t see from the surface, we stop and show you photos and a written change order before we do anything else. The price on the page for the scope we wrote stays the price. No surprises at the door, no arguments after the job.

Are you an authorized Boral dealer or installer? No, we’re an independent Boral service provider. We install and replace Boral products to manufacturer specifications, but we’re not a Boral-authorized contractor, which means we’re free to tell you when a different product would serve your Ventura home better.

Written by Dylan Pace, Owner, Crestview Roofing Co Ventura at Crestview Roofing Co Ventura, serving Ventura and nearby areas.